Producing steroid final products at home

Join us on the topics about producing steroid final products. Our goal is to make people here get 100% sterile and safe steroid final products for injection at the exactly right dosage.

Basics You’ll Need For Almost Every Conversion:
BB: Benzyl benzoate
BA: Benzyl alcohol (make sure that you do not exceed 5% BA for any of the conversions)
Guaiacol: The super solvent
Polysorbate 80: PS80 (for making water suspensions)
EO: Ethyl oleate (for higher concentration and less injection pain, make sure you are not allergic to it.)
For Liquid Orals:
PEG 300: Polyethylene Glycol

For Steroid Powder Transdermal / Cream:
DMSO Gel.
Oils:
Sesame Oil is good, Grape Seed Oil and so is MCT Oil.
Stay away from the thicker oils, and make sure you don’t have an allergy to the oil you’re using (walnut, for example). Check the Viscosity of oils.

Supplies:
Some companies sell sterile vials with the stopper and crimper already on them. This is good if you have only a small amount to make or only convert every once in a while. Remember to use a venting needle with these when adding your final conversion to them. (transfer air out while putting the product in.)

How Do We Go About The General Steps for Brewing At Home?

According to the type of steroid and corresponding ingredients, the steps might vary slightly. Usually, one of the ingredients would be an equivalent of hormone powder while there would be some format of alcohol as another type of ingredient.

However, there is a basic framework that acts as a guideline for creating steroids at home. Let us assume that you have ingredient A, B and C to be mixed for creating a particular kind of steroid. Following would be the steps for doing the same:

1) There is a certain amount or quantity of A, B and C that are to be mixed with a particular proportion in mind. You need to know the ratio. So if the ratio is 5:2:3, then for a 100 gr of the steroid you need to mix 50 gr of A, 20 gr of B and 30 gr of C.

2) There would be a corresponding amount of preferable liquid (in most cases some kind of oil) to be mixed with the other ingredients. Follow the prescribed quantity. So if 100 ml of oil is required for 1 kg of the total mix, use 10 ml of oil for 100 gm of the ingredient mix.

3) You need a clean and sterilized beaker or a container. Mix the ingredients A, B and C well and place them in the beaker or container.

4) Add the required liquid/ oil to the beaker/ container.

5) Put the beaker/ container on heat. Ensure that the level of heat is either low or moderate but never high.

6) Depending on the type of steroid and the method of consumption, you might need to bake the resultant produced or keep it in liquid format.

While these are the general steps for making steroid at home, there can be variations depending on the type of ingredients in use and the type of resultant steroid. Additionally, the preferred method of consumption may also need modification of steps.

You can find many raw powders here; You should use it on your own risk and be careful with your country’s law. Besides, if you don’t like brewing, we are able to offer steroid in oil form, all you need to do is heating and filtration.feel free to contact duosue@chembj.com to get waht you want.

Is it Safe to Make Steroids at Home?
It is like making any other product or cooking a delicacy. If you are following the proper steps to make it would be great in results too. If you do not follow the proper steps than even the best of food and delicacies taste bad. Same would hold true for steroids too. You need to ensure that the proper ingredients are in place and the proper steps are being followed.feel free to contact duosue@chembj.com to get waht you want.

If the ingredients and the preparatory steps are followed properly than homemade steroids are as good as or even better than some of the best ready made products available in the market. All you need to do is to understand the nuances and importance of the right combination of the ingredients and making them through proper steps.feel free to contact duosue@chembj.com to get waht you want.

How to Learn About The Proper Ingredients?
As you might be aware of, there are many versions of steroids. So the first thing to do would be to identify which is the kind of steroid that you are looking to use. Always make it a point to consult an expert in the field. Your body type will allow certain kinds of steroids to settle down in your system faster than others while it may also reject a few types. When you consult a professional, he / she should be able to tell you what would suit your body well and provide with the best results for you.feel free to contact duosue@chembj.com to get waht you want.

Once you have been able to identify the type of steroid best suited for you, it is time to learn about the ingredients required. You could consult the same professional about this query. Alternately, there are powders available which can be mixed with other ingredients to create steroids. However, before buying such products to create your own steroid always make it a point that not only you have consulted your preferred expert but also have gone through expert reviews describing the product to ensure absolute safety.

 

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s